Marker: efficiency and the price of a percentage point
From the pattern area in CAD and the marker length and width, calculates marker and fabric utilization, use per piece, the cost of losses and the price of one percentage point of efficiency.
At a glance
- What question does it answer?
- What the marker efficiency is, how much fabric goes to waste and what one percentage point costs.
- What data is needed?
- The piece area in the marker from CAD.
- How to read the result?
- Look at marker efficiency and fabric utilization: the difference is selvedges and ends. The price of a percentage point shows what improving the marker is worth. Compare markers of one garment on different fabric widths. Example on the default values: Marker efficiency — 83.4%; Fabric utilization with selvedges and ends — 81.1%; Fabric use per piece — 165.8 cm; Fabric loss per piece — 31.4 cm.
Why and how to reason
A marker is the layout of pattern pieces on fabric so that less is wasted. Efficiency shows what share of the marker area is covered by pieces. Formula: piece area ÷ (marker length × width). Width is net of selvedges: 1.5 m − 2 cm = 1.48 m. In the example 12.1 ÷ (9.8 × 1.48) = 83.4%. But real use is higher: fabric is lost at the ends of the lay. Use per piece = (9.8 + 0.15) ÷ 6 = 1.658 m, ideal (no loss) 12.1 ÷ 6 ÷ 1.5 = 1.344 m. Loss is 0.314 m per piece, at RUB 520 a meter that is RUB 163. Each percentage point of efficiency is worth about RUB 10 per piece: roughly what a pattern maker’s extra effort saves. It turns a good marker into roubles.
When to use it
Reach for it when setting fabric consumption norms and discussing the marker with a pattern maker or factory. Data come from CAD: piece area, length and width. It does not fit patterned or napped fabrics where matching is needed (efficiency is lower and should be compared with similar styles), nor the sketch stage without patterns. A consumption norm from a factory price list may differ: check.
How to read the result
For mass apparel a marker efficiency of 80–90% is a normal range, but what is acceptable depends on the item: trousers and dresses waste more than T-shirts. Look at loss per piece in centimeters and roubles, not percent: 31 cm of fabric per item on a run of 2,000 is 628 m. If the value of a percentage point exceeds the cost of improvement (an hour of a pattern maker), improve the marker. If a factory quotes a higher norm than computed, ask for an explanation. Ask the pattern maker for two or three markers and compare them by loss per piece in roubles: a good marker is often found in an hour of work and the saving repeats on every run.
Common mistakes
The usual mistakes: entering marker length in one unit and area in another; using full width without selvedges; forgetting end-of-lay losses; comparing markers for different sizes without their mix. Do not accept efficiency above 92% without checking: it is usually a unit error. Do not enter fabric width from the label: measure the real roll width.
What data is needed?
- The piece area in the marker from CAD.
- Marker length, actual fabric width, selvedges and lay ends.
- Pieces in the marker and the price per meter.
Inputs
| Field | Unit | Value in the example | Meaning |
|---|---|---|---|
| Area of pieces in the marker | m² | 12.1 | From CAD, all pieces and sizes in the marker. |
| Marker length | m | 9.8 | The length of the pattern marker on the fabric in meters. |
| Actual fabric width | m | 1.5 | The actual fabric width in meters per roll, not the nominal one: the marker layout and the fabric use depend on it. |
| Selvedges (total) | cm | 2 | Marker width = fabric width − selvedges. |
| End losses per marker lay (optional) | m | 0.15 | End losses of the lay per marker in meters. Empty: 0. |
| Pieces in the marker | pcs | 6 | How many items one marker yields. |
| Fabric price per meter (optional) | ₽ | 520 | The price of a meter of fabric excl. VAT: for the cost of losses. Empty: money is not calculated. |
How it is calculated
| Step | Formula |
|---|---|
| Marker width | fabric width − selvedges |
| Marker efficiency | piece area ÷ (length × marker width) |
| Use and loss | use = (length + ends) ÷ pieces; loss = use − area per piece ÷ fabric width |
| 1 point of efficiency | (length − area ÷ (width × (E + 1 pt))) ÷ pieces × price per metre |
Worked numbers
Default values from the app; in the interactive version you enter your own.
- Marker efficiency
- 83.4 %Piece area ÷ (length × marker width).
- Fabric utilisation with selvedges and ends
- 81.1 %
- Fabric use per piece
- 165.8 cm
- Fabric loss per piece
- 31.4 cm
- Cost of losses per piece
- 163.22 ₽
- Price of one percentage point per piece
- 10.06 ₽What a 1 point rise in marker efficiency saves.
Data as a table
| Measure | Use |
|---|---|
| Useful part | 134.4 |
| Loss | 31.4 |
Calculate on the actual width and per marker, then take a monthly average. Efficiency of different garments cannot be compared: their geometry differs; compare markers of one garment on different fabric widths. There is no target value: set a rule of thumb from your history.
Nuances and limits
- Using nominal rather than actual width.
- Leaving out selvedges and lay ends.
- Comparing efficiency across different garments.