Patterns, grading, fit and the technological card: from the base block to the measurement chart and tolerances
A review of design and technological preparation: the base and style block, allowances and fit, grading across sizes and heights, the technological card, the fit session, the measurement chart and tolerances, passing files to the factory and protecting patterns. It decides how well the garment will fit the chosen size run, how many sample corrections are needed and how to check that the lot matches the reference.
Why this document
Size fit and fabric consumption are born in the patterns and not at the factory. A grading error gives size returns, extra samples and a dispute with the factory over who is at fault. The document turns the comment “it does not fit” into measurable corrections and tolerances and shows how patterns are tied to consumption and price. The pattern maker, the technologist, the head of production, the category manager and the buyer read it before approving the sample and when accepting the lot. Russian size standards are named carefully (unverified): the final basis is your size chart and the fit on the chosen figure.
At a glance
- What is this document and why is it needed?
- A review of design and technological preparation: the base and style block, allowances and fit, grading across sizes and heights, the technological card, the fit session, the measurement chart and tolerances, passing files to the factory and protecting patterns. It decides how well the garment will fit the chosen size run, how many sample corrections are needed and how to check that the lot matches the reference.
- Who owns the document and how often is it rebuilt?
- The pattern maker and the technologist with the category manager; patterns and the measurement chart are approved at the fit session and reviewed by size returns; kept by the owner of the style.
- What mistakes are the most common?
- Linear grading on all sizes → poor fit at the edges of the run → set steps by zone and check the extreme sizes. Approve a sample by photo only → size discrepancies in the lot → approve by measurements in the measurement chart. Not fixing pattern versions → the factory sews by the old one → a version in every file and in the transfer act.
For whom
- Brand
- A brand sets the fit as part of its identity: the size grid, tolerances, the reference sample; it keeps patterns and the tech pack. The main questions: grading, allowances, the measurement chart, protecting patterns, corrections from returns.
- Retail
- A retailer with a private label sets common size standards for all factories and compares fit across manufacturers. The main questions: one measurement chart, tolerances, accepting the lot by measurements, claims about size and returns.
What it consists of
Construction and fit
- The base block is a drawing of the foundation for a typical figure with minimal ease; the style block adds the silhouette, details and fit for a specific garment.
- Allowances and ease depend on the fabric and silhouette: knitwear stretches, dense fabric does not; seam and hem allowances are part of the pattern area and affect fabric consumption.
- Fit is checked on a mannequin or a live model and not only by the table: the size on paper and on the body differ and returns are built exactly on this.
- The size standards and numbering of different countries differ; Russia has its own system of sizes and heights (unverified: check the current standard) and your chart must be translated into international and internal designations.
Grading
- Grading is the transfer of the base pattern to other sizes and heights in steps: a step for chest, waist, hips, length; the steps are set by a table and not “by eye”.
- Proportional grading takes into account that the steps by zone differ and grow with size; linear (the same step on all sizes) is simpler but gives poor fit at the edges of the run.
- As size grows the pattern area grows, and so do fabric consumption and price; for large sizes take this into account in the price and in the share of the size buy.
- Typical errors: grading without a check on the extreme sizes, the same step for all zones, loss of symmetry, forgotten details (pocket, cuff, lining).
The fit session, the measurement chart and tolerances
- The measurement chart is a list of measurement points (chest width, garment length, sleeve length, shoulder width and others) with target values and tolerances for each size.
- The fit session goes by protocol: photos and measurements, comments as changes (add 1 cm to the chest), a decision on each remark, the sample status (approved, with a correction, rejected).
- The tolerance depends on the measurement point and the fabric: narrow for chest width, wider for length; the values are set by the contract with the factory and not taken from foreign tables (unverified).
- Controlling the lot against tolerances gives the share of garments within tolerance at each point; it is compared with the acceptance threshold (AQL) and the reasons for size returns.
The technological card, files and protecting patterns
- The technological card describes the sequence and type of seams, equipment and unit processing; it becomes the basis for the time standard and the price calculation (the “Sewing technology and work standards” document).
- Patterns are passed to the factory in digital format (design system files) or on paper; a digital file is copied, so limit access, keep versions and keep the original with you.
- Rights to patterns and design are fixed by contract: a ban on passing to third parties and on making overruns, responsibility for leakage (the “Intellectual property” document).
- The reference sample of the approved fit is kept by you and by the factory with a version mark; lot acceptance goes against the reference and the measurement chart.
Brand: how to build fit and control
- Choose the reference figure and size for approving the sample and keep it unchanged between seasons; otherwise the fit “drifts”.
- Set up one measurement chart for the category and add measurement points only when really needed: too many points slow down acceptance.
- Analyze size returns and match them with the measurement chart: a mass return “too small” or “too big” in one size points to grading and not to taste.
- Keep versions of patterns and the history of corrections: when the factory changes you move a file and not memory.
- Give the factory not only patterns but also the measurement chart with tolerances and the reference: then acceptance goes by numbers and not by the feeling “looks alike”.
Retail: one standard for several factories
- Introduce one size chart of the chain and tolerances for all factories; without it the same size from different manufacturers fits differently and returns grow.
- Control the fit at the distribution center entrance by sample measurement against the measurement chart and tie the result to a claim on the factory.
- For a private label approve patterns centrally and hand identical files to factories; factories must not change patterns on their own.
- Compare the size structure of the buy with the fact of returns: if the extreme sizes are returned more often, check the grading on them.
- Collect size returns by factory and pattern: a total percentage hides a problem factory or size.
Where the data comes from
| Data source | Fields |
|---|---|
| Patterns and the design system: base drawings, grading, piece areas | steps by size and zone, areas, file versions |
| Fit sessions and samples: protocols, photos, measurements | comments, corrections, sample status, the approved fit |
| The measurement chart and tolerances | measurement points, target values, tolerances by size |
| Size returns and claims | size, return reason, share by size and by factory |
How to build it step by step
- Step 1: Determine the size run and the reference size, fix the size table and the grading steps by zone.
- Step 2: Build the base and style block, set allowances and ease by fabric and silhouette.
- Step 3: Hold the fit session on the reference size by protocol: measurements, photos, decisions on each remark.
- Step 4: Make corrections to the patterns, update the version and approve the sample; keep the reference.
- Step 5: Grade by the step table and check the extreme sizes on samples or in a virtual fit.
- Step 6: Draw up the measurement chart by size with tolerances and the technological card; hand the factory the set.
- Brand: Step 7: On the first lot measure a sample against the chart, calculate the share within tolerance by point and agree corrections with the factory.
- Retailer: Step 7: Introduce sample measurement at the distribution center entrance and tie the result to size claims.
- Brand: Step 8: After the season compare size returns with the chart and correct the grading or tolerances in the patterns.
- Retailer: Step 9: Once a season compare the fit of factories by measurements and revise the common standard.
Formulas
| Measure | Formulas | Note |
|---|---|---|
| Size and pattern area | A(x) ≈ a + b × x, where x is the chest girth and A the garment pattern area | The coefficients a and b are calculated across the sizes of the run; the slope b shows how many square meters of fabric each centimeter of girth adds. |
| Share within tolerance | p = number of garments with |d| ≤ t / n × 100, where d is the deviation from the target, t the tolerance, n the sample size | Calculate for each measurement point separately; draw the overall conclusion from the worst point. |
| Mean offset and spread | m = Σ d_i / n; s = √(Σ (d_i − m)² / (n − 1)) | A shift of the mean points to a pattern or fit error, a large spread to unstable sewing. |
Formulas in notation
- Pattern area by size
A(x) = a + b·x
A linear relation of the pattern area to the chest girth across the sizes of the run; b is the price of a centimeter of girth in fabric.
Worked example
Controlling a lot by the measurement chart: 20 garments of size M (illustrative deviations of measurements from target values, cm)
| Measurement point | Target, cm | Tolerance ±, cm | Mean offset, cm | Spread (SD), cm | Within tolerance, % |
|---|---|---|---|---|---|
| Chest width | 52.0 | 1.0 | 0.12 | 0.72 | 85 |
| Garment length | 68.0 | 1.5 | 0.08 | 0.93 | 90 |
| Sleeve length | 60.0 | 1.0 | 0.36 | 0.71 | 80 |
| Shoulder width | 41.0 | 0.8 | 0.09 | 0.46 | 95 |
For sleeve length the mean is shifted to plus and the fewest garments are within tolerance: this points to the patterns or fit and not to a random spread of sewers. Treat a sample of 20 garments as a guide; a decision about the lot needs a sample by the acceptance plan.
Figures
- points
- regression line: y = −0.376 + 0.022·x
Data as a table
| Chest girth, cm | Pattern area, m² | |
|---|---|---|
| 88 | 1.52 | S |
| 92 | 1.6 | M |
| 96 | 1.68 | L |
| 100 | 1.78 | XL |
Grading: pattern area across the sizes of the run. The pattern area grows with the chest girth almost linearly; the slope of the line shows the price of a size in fabric.
Data as a table
| Measure | Within tolerance |
|---|---|
| Chest width | 85 |
| Garment length | 90 |
| Sleeve length | 80 |
| Shoulder width | 95 |
Share of garments within tolerance by measurement point, %. The point with the smallest share determines the decision on the lot and the direction of corrections.
The fit approval cycle. Corrections return to the patterns, the version changes, the sample is approved only after measuring against the chart.
- Construction and grading → Sample
- Sample → Fit session and measurements
- Fit session and measurements → Pattern corrections, new version; Approval and the reference
- Pattern corrections, new version → Sample
- Approval and the reference
Specifics by category
- Apparel
- Apparel: grading by girths and height, fit depends on the fabric (knit, woven, stretch); the measurement chart is built differently for tops, bottoms and dresses.
- Footwear
- Footwear: instead of garment patterns the last works and the size run goes by foot length and width; last grading across the run and not by pattern steps (the “Footwear and leather goods production” document).
- Accessories
- Accessories: the size is more often one or a limited run (belts, gloves, headwear); measurement points and tolerances are set by dimensions and fit and grading is applied sparingly.
- Kids
- Children’s: sizes go by height and age and not by girths and grow faster; for safety the sizes of cords, hoods and small details are checked (TR CU 007/2011, unverified) and the run is made frequent.
- Men
- Men’s: grading by chest girth and height is stable, suit groups need separate tables and tolerances on shoulders and sleeve length are stricter.
- Women
- Women’s: size fit depends on silhouette and fabric more than on figures; tolerances on hips and chest are set separately, and differences between brands in size numbering are large, so a chart of your own is needed.
Common mistakes
- Linear grading on all sizes → poor fit at the edges of the run → set steps by zone and check the extreme sizes.
- Approve a sample by photo only → size discrepancies in the lot → approve by measurements in the measurement chart.
- Not fixing pattern versions → the factory sews by the old one → a version in every file and in the transfer act.
- Copy tolerances from a foreign table → acceptance catches the unnecessary or misses the necessary → set tolerances by fabric and measurement point in the contract.
- Not matching size returns with the chart → the causes stay unknown → tie returns to measurements and grading.
Russian specifics
- Size standards for garments in Russia rely on state standards for typical figures; check the number and currency of the standard before use and do not copy numbering from foreign tables (unverified).
- Brand: on the label and in the product card state the size by the system accepted in the country and, where needed, the match to the international one; a mismatch of size with the fact is a ground for a customer claim.
- Retailer: acceptance of the lot by measurements is formalized by an act with a sample and tolerances from the contract; the result is the basis for a claim on the factory over size.
- Children’s garments are subject to the safety requirements of the technical regulation (TR CU 007/2011): check the current wording, the sizes of small details and fastenings (unverified).